The main objective of this work is the migration of the tail control system of an underwater biomimetic robot from I2C communication to the CAN bus. To achieve this goal, the project involves adapting the logic of the pre-existing firmware to the new hardware architecture, including the configuration and programming of ESP32 microcontrollers. It also aims at integrating servomotors equipped with a native CAN interface in order to reproduce the sinusoidal movement and effectively coordinate the actuation of the three propulsive joints. A further fundamental objective of the work is to set up a system for the acquisition and visualization of data from the servomotors and the inertial measurement units (IMU). This step is essential to experimentally verify in the laboratory the correspondence between the requested theoretical movement and the actual physical behavior observed in the system.

Il presente lavoro ha come obiettivo principale la migrazione del sistema di controllo della coda di un robot biomimetico subacqueo da una comunicazione I2C al bus CAN. Per raggiungere questo scopo, il progetto prevede l’adattamento della logica del firmware preesistente alla nuova architettura hardware, includendo la configurazione e la programmazione di microcontrollori ESP32. Si mira inoltre all’integrazione di servomotori dotati di interfaccia CAN nativa, al fine di riprodurre il movimento sinusoidale e coordinare in modo efficace l’azionamento dei tre giunti propulsivi. Un ulteriore obiettivo fondamentale del lavoro consiste nel predisporre un sistema per l’acquisizione e la visualizzazione dei dati provenienti dai servomotori e dalle unità di misura inerziale (IMU). Questo passaggio è essenziale per verificare sperimentalmente in laboratorio la corrispondenza tra il movimento teorico richiesto e il reale comportamento fisico osservato nel sistema.

Studio e progettazione di un sistema propulsivo per robot biomimetici basato su CAN bus e servomotori BLDC

SECCI, BIANCA
2025/2026

Abstract

The main objective of this work is the migration of the tail control system of an underwater biomimetic robot from I2C communication to the CAN bus. To achieve this goal, the project involves adapting the logic of the pre-existing firmware to the new hardware architecture, including the configuration and programming of ESP32 microcontrollers. It also aims at integrating servomotors equipped with a native CAN interface in order to reproduce the sinusoidal movement and effectively coordinate the actuation of the three propulsive joints. A further fundamental objective of the work is to set up a system for the acquisition and visualization of data from the servomotors and the inertial measurement units (IMU). This step is essential to experimentally verify in the laboratory the correspondence between the requested theoretical movement and the actual physical behavior observed in the system.
2025
2026-10-22
Study and design of a propulsive system for biomimetic robots based on CAN bus and BLDC servomotors
Il presente lavoro ha come obiettivo principale la migrazione del sistema di controllo della coda di un robot biomimetico subacqueo da una comunicazione I2C al bus CAN. Per raggiungere questo scopo, il progetto prevede l’adattamento della logica del firmware preesistente alla nuova architettura hardware, includendo la configurazione e la programmazione di microcontrollori ESP32. Si mira inoltre all’integrazione di servomotori dotati di interfaccia CAN nativa, al fine di riprodurre il movimento sinusoidale e coordinare in modo efficace l’azionamento dei tre giunti propulsivi. Un ulteriore obiettivo fondamentale del lavoro consiste nel predisporre un sistema per l’acquisizione e la visualizzazione dei dati provenienti dai servomotori e dalle unità di misura inerziale (IMU). Questo passaggio è essenziale per verificare sperimentalmente in laboratorio la corrispondenza tra il movimento teorico richiesto e il reale comportamento fisico osservato nel sistema.
File in questo prodotto:
File Dimensione Formato  
TESI-SECCI-BIANCA.pdf

accesso aperto

Descrizione: Studio e progettazione di un sistema NGC per robot biomimetici. Sviluppo prototipale di un sistema propulsivo basato su CAN BUS per il pesce robot in dotazione al laboratorio.
Dimensione 6.37 MB
Formato Adobe PDF
6.37 MB Adobe PDF Visualizza/Apri

I documenti in UNITESI sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/20.500.12075/29633