The measurement of the electrical parameters R, C, and L plays a fundamental role in the characterization of electronic components and circuits. This work analyzes the main methods employed for the measurement of these parameters, with particular focus on bridge-based techniques, transient response methods, and the voltammetric method. The first part of the thesis examines the equivalent models of real components and the main methods used for the measurement of resistive, capacitive, and inductive parameters. An experimental comparison is also carried out between the Rohde & Schwarz LCX200 meter and the Moku:Go platform by Liquid Instruments, through a measurement campaign performed on different components and over various value ranges, with the aim of evaluating and comparing their performance. Subsequently, a measurement system based on an Arduino Uno board, and specifical- ly on the ATmega328P microcontroller integrated into the board, is developed and characterized for the implementation of an RCL meter. The system is subjected to several experimental tests for the measurement of individual resistors and capacitors, as well as series and parallel RC networks. Its performance is evaluated by comparing the measured values with reference values. In the final part of the thesis, an ohmmeter based on the bridge method is developed, using an Arduino Uno for voltage acquisition through its integrated analog-to-digital converter and a buffer stage. The system is characterized over several measurement ranges through a measurement campaign covering a wide range of resistance values. The results are compared with those obtained using the previously implemented me- thod and with reference values measured using the LCX200. The uncertainty analysis highlights the good performance of the bridge method for medium-to-high resistance values, whereas a significant increase in relative error is observed for low resistance values. This behavior highlights the greater dependence of the bridge method on the characteristics of the components used and on the operating conditions of the circuit, particularly with regard to thermal effects and parasitic resistances.

La misura dei parametri elettrici R, C e L riveste un ruolo fondamentale nella carat- terizzazione dei componenti e dei circuiti elettronici. Il presente lavoro analizza i prin- cipali metodi impiegati per la misura di tali parametri, con particolare attenzione alle tecniche basate su ponte, sulla risposta transitoria e sul metodo voltamperometrico. Nella prima parte della tesi vengono analizzati i modelli equivalenti dei componenti reali e i principali metodi di misura dei parametri resistivi, capacitivi e induttivi. Viene inoltre condotto un confronto sperimentale tra il misuratore LCX200 di Rohde & Schwarz e la piattaforma Moku:Go di Liquid Instruments, attraverso una campagna di misure effettuata su differenti componenti e intervalli di valore, al fine di valutarne e confrontarne le prestazioni. Successivamente viene sviluppato e caratterizzato un sistema di misura basato su una scheda Arduino Uno e, in particolare, sul microcontrollore ATmega328P inte- grato nella scheda, finalizzato alla realizzazione di un RCL meter. Il sistema viene sottoposto a diverse prove sperimentali per la misura di resistenze e capacità isolate e di reti RC serie e parallelo, valutandone le prestazioni mediante il confronto con valori di riferimento. Nella parte conclusiva viene realizzato un ohmetro basato sul metodo a ponte, utiliz- zando Arduino Uno per l’acquisizione delle tensioni mediante il convertitore analogico- digitale integrato e uno stadio buffer. Il sistema viene caratterizzato attraverso diverse portate, mediante una campagna di misure su un ampio intervallo di valori resistivi. I risultati vengono confrontati con quelli ottenuti mediante il metodo precedentemen- te implementato e con i valori di riferimento misurati tramite l’LCX200. L’analisi dell’incertezza evidenzia un buon comportamento del metodo a ponte per valori di resistenza medio-alti, mentre per le basse resistenze si osserva un significativo aumen- to dell’errore relativo. Tale comportamento mette in evidenza la maggiore dipendenza del metodo a ponte dalle caratteristiche dei componenti impiegati e dalle condizio- ni operative del circuito, in particolare per quanto riguarda gli effetti termici e le resistenze parassite.

Studio ed implementazione dei principali metodi per la misura dei parametri LCR

CARBONARI, THOMAS
2025/2026

Abstract

The measurement of the electrical parameters R, C, and L plays a fundamental role in the characterization of electronic components and circuits. This work analyzes the main methods employed for the measurement of these parameters, with particular focus on bridge-based techniques, transient response methods, and the voltammetric method. The first part of the thesis examines the equivalent models of real components and the main methods used for the measurement of resistive, capacitive, and inductive parameters. An experimental comparison is also carried out between the Rohde & Schwarz LCX200 meter and the Moku:Go platform by Liquid Instruments, through a measurement campaign performed on different components and over various value ranges, with the aim of evaluating and comparing their performance. Subsequently, a measurement system based on an Arduino Uno board, and specifical- ly on the ATmega328P microcontroller integrated into the board, is developed and characterized for the implementation of an RCL meter. The system is subjected to several experimental tests for the measurement of individual resistors and capacitors, as well as series and parallel RC networks. Its performance is evaluated by comparing the measured values with reference values. In the final part of the thesis, an ohmmeter based on the bridge method is developed, using an Arduino Uno for voltage acquisition through its integrated analog-to-digital converter and a buffer stage. The system is characterized over several measurement ranges through a measurement campaign covering a wide range of resistance values. The results are compared with those obtained using the previously implemented me- thod and with reference values measured using the LCX200. The uncertainty analysis highlights the good performance of the bridge method for medium-to-high resistance values, whereas a significant increase in relative error is observed for low resistance values. This behavior highlights the greater dependence of the bridge method on the characteristics of the components used and on the operating conditions of the circuit, particularly with regard to thermal effects and parasitic resistances.
2025
2026-10-22
Study and implementation of the main methods for measuring LCR parameters
La misura dei parametri elettrici R, C e L riveste un ruolo fondamentale nella carat- terizzazione dei componenti e dei circuiti elettronici. Il presente lavoro analizza i prin- cipali metodi impiegati per la misura di tali parametri, con particolare attenzione alle tecniche basate su ponte, sulla risposta transitoria e sul metodo voltamperometrico. Nella prima parte della tesi vengono analizzati i modelli equivalenti dei componenti reali e i principali metodi di misura dei parametri resistivi, capacitivi e induttivi. Viene inoltre condotto un confronto sperimentale tra il misuratore LCX200 di Rohde & Schwarz e la piattaforma Moku:Go di Liquid Instruments, attraverso una campagna di misure effettuata su differenti componenti e intervalli di valore, al fine di valutarne e confrontarne le prestazioni. Successivamente viene sviluppato e caratterizzato un sistema di misura basato su una scheda Arduino Uno e, in particolare, sul microcontrollore ATmega328P inte- grato nella scheda, finalizzato alla realizzazione di un RCL meter. Il sistema viene sottoposto a diverse prove sperimentali per la misura di resistenze e capacità isolate e di reti RC serie e parallelo, valutandone le prestazioni mediante il confronto con valori di riferimento. Nella parte conclusiva viene realizzato un ohmetro basato sul metodo a ponte, utiliz- zando Arduino Uno per l’acquisizione delle tensioni mediante il convertitore analogico- digitale integrato e uno stadio buffer. Il sistema viene caratterizzato attraverso diverse portate, mediante una campagna di misure su un ampio intervallo di valori resistivi. I risultati vengono confrontati con quelli ottenuti mediante il metodo precedentemen- te implementato e con i valori di riferimento misurati tramite l’LCX200. L’analisi dell’incertezza evidenzia un buon comportamento del metodo a ponte per valori di resistenza medio-alti, mentre per le basse resistenze si osserva un significativo aumen- to dell’errore relativo. Tale comportamento mette in evidenza la maggiore dipendenza del metodo a ponte dalle caratteristiche dei componenti impiegati e dalle condizio- ni operative del circuito, in particolare per quanto riguarda gli effetti termici e le resistenze parassite.
File in questo prodotto:
File Dimensione Formato  
Tesi_L_IETD_Thomas_Carbonari.pdf

accesso aperto

Dimensione 17.63 MB
Formato Adobe PDF
17.63 MB Adobe PDF Visualizza/Apri

I documenti in UNITESI sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/20.500.12075/29677